Integra Serial Control Protocol

Integra Serial Control Protocol

Communication protocol
Abbreviation	ISCP
Developers	Intergra and Onkyo
Introduction	August 22, 2003 (2003-08-22)

Integra Serial Control Protocol (ISCP) is a proprietary command protocol for home audio and home theater equipment, developed by Onkyo and its Integra division. Controllers use it to operate AV receivers, preamplifiers, and disc players remotely, with commands for power, input selection, volume, and status queries. Some Pioneer products also use ISCP, after Pioneer transferred its home AV business to Onkyo in March 2015.

ISCP was designed for RS-232 serial links. A later variant, eISCP (Ethernet ISCP), carries the same messages over TCP/IP, so IP-based home automation systems and software controllers can control the equipment over a network.

As of February 2025, the latest version of the specification is 1.53.

ISCP over RS-232C

Hardware characteristics

ISCP over serial uses a simple 3-wire RS-232C connection with the following parameters:

• 9600 baud
• 8 data bits
• 1 stop bit
• No parity
• No flow control

The physical connector is a 9-pin female D-sub:

• Pin 2: Transmit
• Pin 3: Receive
• Pin 5: Signal ground

A straight-through cable is used to connect the device to a PC or controller.

Message format

Messages are ASCII text and follow this structure:

ISCP Message Format

Offset	Octet	0								1								2								3
Octet	Bit	0	1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16	17	18	19	20	21	22	23	24	25	26	27	28	29	30	31
0	0	Start Character (!)								Destination Unit type								Command↴
4	32	↪cmd cont
8	64	Parameter
12	96
⋮	⋮
264	2112																	End Character ("[CR]"or"[LF]"or"[CR][LF]")

Start Character: 8 bits

Start Character of ISCP message: !

Destination Unit type Character: 8 bits

Indicate type; discovery x and p, Zone 1-8

Command: 32 bits

Command/Status/Question/Event Notice type

Parameter: Variable length

Command/Status/Question/Event Notice parameter

End Character: 8-16 bits

indicate end of ISCP message: [CR] or [LF] or [CR][LF]

A typical controller → device message for "Power On" is:

1st	2nd	3rd-5th			6th-		last
!	1	P	W	R	0	1	[CR]

where:

• ! is the start character
• 1 is the destination unit type (1 = receiver)
• PWR01 is the ISCP command and parameter
• [CR], [LF], or [CR][LF] terminates the message

A device → controller response indicating "Power Standby" may look like:

1st	2nd	3rd-5th			6th-		last
!	1	P	W	R	0	0	[EOF]

Special characters used by the protocol:

Symbol	Meaning	ASCII
[CR]	Carriage return	0x0D
[LF]	Line feed	0x0A
[EOF]	End of file	0x1A

Ethernet ISCP (eISCP)

Ethernet Integra Serial Control Protocol

Communication protocol
Abbreviation	eISCP
Developers	Intergra and Onkyo
Based on	ISCP over RS232
Ports	TCP 60128, UDP 60128, for Auto Detect using broadcast (v1.19)

With the introduction of network-enabled receivers, ISCP was encapsulated for transport over TCP/IP. This form is known as eISCP or ISCP over Ethernet.

Auto Detect ISCP over Ethernet

Receivers (introduced after 2011, with version 1.19 or higher) support automatic discovery on a local network, allowing controllers to find compatible devices without manual configuration. This allows client for quicker setup and without knowing the IP address in advance.

A controller starts discovery by broadcasting a "device search" message over UDP to port 60128. Onkyo and Integra receivers answer a query addressed to unit type x. Pioneer receivers expect p instead.

The protocol doesn't list any multicast support, so inter Subnet of auto discovery is not supported.

Each receiver that supports ISCP replies with a single line giving its model name, control port, regional variant, and a unique identifier, usually derived from its network address. The controller can use these fields to show a readable device name and open a control session on the reported port. The specification describes no multicast option, and broadcasts do not cross routers, so discovery only finds receivers on the controller's own subnet.

eISCP packet format

An eISCP packet consists of a binary header followed by the standard ISCP message:

eISCP header Format

Offset	Octet	0								1								2								3
Octet	Bit	0	1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16	17	18	19	20	21	22	23	24	25	26	27	28	29	30	31
0	0	I								S								C								P
4	32	Header size (16)
8	64	data size
12	96	version (1)								reserved (000)
16	128	data (1 or more eISCP Messages)
20	160
⋮	⋮

Header Size: 32 bits

Size of the eISCP header. Currently 0x00000010 (big-endian)

Data Size: 32 bits

Length of the eISCP data section (big-endian)

Version: 8 bits

ISCP version, currently 0x01

Reserved: 24 bits

Reserved for future extensions.

eISCP Message Format

Offset	Octet	0								1								2								3
Octet	Bit	0	1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16	17	18	19	20	21	22	23	24	25	26	27	28	29	30	31
0	0	Start Character (!)								Destination Unit type								Command↴
4	32	↪cmd cont
8	64	Parameter
12	96
⋮	⋮
264	2112																	End Character ("[CR]"or"[LF]"or"[CR][LF]")

Start Character: 8 bits

Start Character of eISCP message: !

Destination Unit type Character: 8 bits

Indicate type; discovery x and p, Zone 1-8

Command: 32 bits

Command/Status/Question/Event Notice type

Parameter: Variable length

Command/Status/Question/Event Notice parameter

End Character: 8-16 bits

indicate end of eISCP message: [CR] or [LF] or [CR][LF]

Security

Further information: Computer security, Network security, Cyber resilience, and Operational technology § Security

The eISCP specification defines no built-in authentication, encryption or access control for the receiver's control connection. Commands and status messages are transmitted in clear text over TCP. A controller that can establish a connection to the receiver's control port can send commands and receive status updates.

Access to port therefore determines which controller can control the receiver. Exposing the receiver to an untrusted network allows any controller on that network to interact with the receiver through eISCP.

The protocol has the following security implications:

• controller with access to the control port can issue commands etc.
• Commands and metadata are readable by systems able to capture the network traffic.
• Device discovery uses UDP broadcasts or unicast, without authentication.

In practice Network-level controls, such as firewall rules and network segmentation, can restrict access to the receiver. These controls are external to eISCP.

Communication flow

ISCP defines theree messages types commands, queries and status information between a controller and a receiver.

Command message

A controller sends a command message to change a receiver setting, such as power or volume. The receiver also provides ''unsolicited feedback'': if the receiver's internal status changes for any reason (for example, due to front-panel operation or another controller), it sends a ''status message'' to all connected controllers. These messages allow controllers to update their stored receiver state.

Question message

A question message requests the current state of a receiver function. The setting remains unchanged. The receiver replies with a status message, which the controller can use to obtain the receiver's state after connecting, check its stored state, or recover after losing synchronization.

Event notice

The receiver sends event notices when its state changes, including changes made through its front-panel controls or by another controller, and reports the new state to connected controllers. No prior request is required. In eISCP, persistent connections allow controllers to receive these notifications as changes occur.

Command types

ISCP commands control receiver functions such as power, volume, input selection and playback. The specification lists supported commands and parameters for each receiver model.

Parameters specify the requested operation. For example, PWR01 switches the receiver on, while PWRQSTN requests its power status. Depending on the command and model, parameters can select a value, step through settings or query the current state.

Set a value

A parameter selects a setting, such as 00 for standby or 01 for power on with the PWR command.

Step or cycle through settings

Parameters such as UP, DOWN and TG adjust a setting or cycle through its available states. Their meaning depends on the command.

Query the current state

The QSTN parameter requests a status message from the receiver.

Commands include the following groups:

System control

PWR, SLP, RST, APD, ECO - power, sleep, reset, and energy management.

Volume and muting

MVL, AMT, CMT, SWL, CTL, TCL - master volume, muting, and per-channel levels.

Tone and EQ

TFR, TFW, TFH, TCT, TSR, TSB, TSW, ACE, EQS, STW - bass, treble, and equalization across speaker groups.

Speaker configuration

SPA/SPB, SPL, SPI, SPD - zone selection, layout, size, and distance.

Input and signal selection

SLI, SLR, SLA, VSL, ISS - source selection, record-out, and input management.

Listening and processing modes

LMD, DIR, LTN, RAS, ADY, ADQ, ADV, DVL, AEQ - surround modes, room correction, and night processing.

Video and HDMI control

HDO, HAO, HAS, CEC, RES, VPM, VWM, HSF - output routing, resolution, and picture modes.

Information and display

DIF, IFA, IFV, IFN, FLD - device, audio, video, and network status.

Networking and system

FWV, UPD, POP, TPD - firmware, updates, UI messages, and thermal data.

Tuner and radio

TUN, PRS, PRM, and model-specific RDS, DAB, XM, Sirius, and HD Radio commands.

Advanced calibration

AEO, DSS, DBC, PCT, PCP - room correction and phase control.

Security and locking

KYL, IRL - front-panel and IR lockout.

Network and streaming control

NTC, NAT, NAL, NTI, NTM, NTR, NST, NMS, NLS, NLA, NLT, NJA, NSV, NKY, NPU, NCP, NDS, NBS, NRI - transport keys, menu navigation, playback status, metadata (artist/album/title), list rendering, album art, service selection, on-screen keyboard input, popup UI messages, device/network status, and receiver capability discovery.

History

Version 1.00 (2003)

The first edition of the specification was published on 22 August 2003.

Version 1.03 (2005)

Added Zone 3 commands.

Version 1.05 (2005)

Added commands for docks connected through RI.

Version 1.19 (2011)

Added automatic device discovery over Ethernet.

Version 1.22 (2012)

Added command tables for Blu-ray players and televisions controlled through RIHD. RI, Universal Port and network/USB commands were moved into separate tables.

Version 1.39 (2017)

Changed command parameters for Chromecast built-in.

Version 1.40 (2017)

Changed command parameters for Play-Fi and the play queue.

Version 1.50 (2023)

Added Auro-3D and Auro Surround parameters to the listening-mode command.

Version 1.53 (2025)

Added infrared and front-panel locking commands for 2021 and 2023 models. This edition was published on 3 February 2025.

List of supported eISCP devices

This chapter provides an overview of known Integra, Onkyo, Pioneer and Tascam products that implement eISCP.

Onkyo

• Onkyo TX-L20D
• Onkyo TX-L50
• Onkyo TX-NR414
• Onkyo TX-NR509
• Onkyo TX-NR525
• Onkyo TX-NR535
• Onkyo TX-NR575E
• Onkyo TX-NR616
• Onkyo TX-NR636
• Onkyo TX-NR646
• Onkyo TX-NR656
• Onkyo TX-NR676E
• Onkyo TX-NR686
• Onkyo TX-NR696
• Onkyo TX-NR818
• Onkyo TX-RZ50
• Onkyo TX-RZ70
• Onkyo TX-RZ810
• Onkyo TX-RZ830
• Onkyo TX-RZ900
• Onkyo TX-RZ1100
• Onkyo TX-8130
• Onkyo TX-8150
• Onkyo TX-8250
• Onkyo TX-8260
• Onkyo TX-8270
• Onkyo TX-8390
• Onkyo TX-8470
• Onkyo R-N855
• Onkyo CS-N575D
• Onkyo CR-N755
• Onkyo CR-N765
• Onkyo CR-N775D
• Onkyo HT-S7805
• Onkyo NS-6130
• Onkyo NS-6170
• Wireless Audio System NCP-302

Integra

• Integra DTM-6
• Integra DRX-5.2
• Integra DTR 30.7
• Integra DTR 40.7

Pioneer (models after 2016)

• Pioneer VSX-LX101
• Pioneer VSX-LX103
• Pioneer VSX-LX104
• Pioneer VSX-LX302
• Pioneer VSX-LX303
• Pioneer VSX-LX503
• Pioneer VSX-LX504
• Pioneer VSX-S520D
• Pioneer VSX-831
• Pioneer VSX-832
• Pioneer VSX-932
• Pioneer VSX-933
• Pioneer VSX-935
• Pioneer VSX-1131
• Pioneer SC-LX701
• Pioneer SC-LX901
• Pioneer SX-N30
• Pioneer SX-S30DAB
• Pioneer NC-50DAB
• Pioneer N-50AE
• Pioneer N-70AE
• Pioneer XC-HM86D
• Pioneer MRX-3
• Pioneer MRX-5

Tascam

• PA-R100
• PA-200
• AG-D500

See also

• RS-232
• Home automation
• Onkyo

Client integrations

• Home Assistant, Onkyo
• Homey, Onkyo Receiver
• Android Enhanced Music Controller lite (onpc)
• Android Enhanced Music Controller (onpc)
• iOS Enhanced Music Controller
• openHAB add-on Onkyo

Open source integration of eISCP

• GitHub: go-onkyo
• GitHub: mkulesh/onpc (Enhanced Music Controller)
• GitHub: Python3 library aioonkyo (Used by Home Assistant)
• GitHub: eISCP to RS232 ISCP bridge eiscp_bridge
• GitHub: eISCP to MQTT bridge eiscp2mqtt